The Ra Ladder on Turned Parts: What Each Step Down Costs
By CHX Metal Engineering Team · Published 2026-11-14
For most turned parts Ra 1.6 µm as-machined is the workhorse and Ra 0.8 µm covers sealing faces; calling Ra 0.2 everywhere can roughly double finishing cost without adding function. Put smoothness only where a seal, bearing seat or cosmetic face needs it - on 13 years of drawings, that has usually been one or two features per part.
Most Ra trouble starts with a default nobody chose
A stainless bushing came through quoting last month with Ra 0.2 µm called on every surface. We asked which faces actually seal or show; the answer was “just in case”. Nobody had decided it - the call had been copied forward from an older print, and every copy made it more legitimate. That one call forced a secondary polishing operation on a part whose working faces were two, because as-turned surfaces off fresh tooling land near Ra 1.6–3.2 µm and no feed adjustment will take them to 0.2.
The habit is understandable. A tolerance band gets absorbed by good tooling and a stable setup, so escalating it feels free. Finish does not work that way: every step down the Ra ladder stops being a cutting parameter and becomes a separate process with its own setup, inspection and scrap risk. Nobody wins from the escalated call - the buyer pays for smoothness the assembly never touches.
What each step down the ladder costs
On turned work the ladder looks like this in practice:
| Ra call | Typical route on turned work | Cost meaning |
|---|---|---|
| Ra 3.2 µm | Ordinary turning, insert near end of life acceptable | Base price |
| Ra 1.6 µm | Steady feed, fresh insert, sound setup | Base price |
| Ra 0.8 µm | Fine feed pass, sharp nose radius, rigid workholding | Small premium |
| Ra 0.4 µm | Usually a second operation: grinding or polishing | Visible adder |
| Ra 0.2 µm | Lapping or precision polishing, controlled by hand | Can double finishing cost |
The jump is not linear, and the table understates it. I once polished a batch of aluminium bushings to a finish so good the parts were beautiful and also scrap - the polishing had pulled the diameter out of its band. Since then, any finish call tighter than the function needs gets a polite question before the quote goes out, because I have paid for that lesson once already.
Where smoothness actually earns its keep
Real candidates are short: a sealing face a gasket or O-ring rides on, a bearing seat, a groove the seal lip travels across, a face a customer touches and judges the whole part by. Internal bores nobody sees, faces hidden under a cover, surfaces that only locate - those take the as-machined finish and never complain.
Small-part work has a quiet advantage here. Our Tsugami Swiss-type lathes - 70 of them across the floor - turn small diameters with fine feeds and short stick-out, and as-machined surfaces off those machines regularly satisfy a 0.8 call with no second operation. Rigidity and short overhang do half the job before anyone polishes anything. What the machines cannot reach, the finish becomes a real process decision instead of a tooling detail - and that is exactly where the drawing should say so.
Ra, Rz, and the disputes that start at inspection
Ra averages the deviations; Rz looks at the extremes between highest peak and deepest valley. A surface can pass its Ra call and fail an Rz call on the same face, because one isolated scratch drags Rz up while barely moving the average. Neither number is wrong - they describe different things - which is precisely why the argument happens: the print says Ra, the incoming gauge reports Rz, and both inspectors are reading their instruments correctly.
We spent most of an afternoon proving exactly this once, on a rejection where the customer’s instrument used a different sampling cutoff. The part was fine; the parameters were not aligned. Since then, parameter, cutoff and lay direction get confirmed in writing at first article, not at the dispute. It is a five-minute email that has prevented more friction than any process improvement on the floor.
How finish calls get handled before quoting
When a request arrives, finish calls are read against function before price is calculated. An escalated call comes back with a question attached, and if the answer is uncertain, the minimum order of one piece settles it cheaply: a first article with a profilometer reading runs in 3–7 days, so the surface is measured on real metal before a production run of 7–15 days is committed. Tight diameters are quoted at ±0.005 mm where the fit needs it; the finish call gets the same treatment - as tight as the function demands, and no tighter.
This page deliberately stays on the numbers and the disputes. For the wider map of what happens after machining - anodizing types, plating, passivation, and how to write finish notes on a drawing - see our CNC surface finish guide and the surface treatment hub.
The plant behind this runs 220 machines in Shajing, Bao'an, Shenzhen — 100 machining centres, 30 of them 3+2, 50 CNC lathes and 70 Tsugami Swiss-type lathes — across 5,000 m² with 100+ staff, producing up to 5 million pieces a month. Production runs 7–15 days once a design is settled. Terms are EXW Shenzhen only - we are happy to recommend reliable freight forwarders.
Thirteen years in, prints that call Ra 0.2 everywhere still arrive every week. Fewer of them leave our quoting desk unchanged. That five-minute conversation about which faces actually matter is usually where the money is.
Machining capacity behind this article
- Equipment: 220 machines — 100 machining centres (30 of them 3+2), 50 CNC lathes, 70 Tsugami Swiss-type lathes.
- Tolerance: ±0.005 mm on critical features; anything unmarked defaults to ISO 2768-m.
- Volume: up to 5 million pieces a month; prototyping 3–7 days, production 7–15 days.
- Materials: 6061/7075 aluminium, 303/304/316 stainless, H59 brass, copper, TC4 titanium, carbon steel.
- Footprint: 5,000 m² in Shajing, Bao'an, Shenzhen; 100+ staff; founded 2013.
- Terms: EXW Shenzhen only — we are happy to recommend reliable freight forwarders.
Address: Building B, 3rd Floor, Haosan Maozhoushan Industrial Zone, Buyong Community, Shajing Street, Bao'an District, Shenzhen | Tel: +86-755-27427365 | Email: mc@chxmetal.com
Frequently asked questions
What Ra should I specify on a CNC turned part?
Start from function: Ra 1.6 um as-machined suits most surfaces, Ra 0.8 um covers sealing faces and bearing seats, and anything below 0.8 needs a second operation such as grinding or polishing. Calling a tight finish on every surface adds cost to operations the assembly never touches.
Why does Ra 0.2 cost so much more than Ra 0.8?
Ra 0.8 is reachable by cutting parameters - fine feed, sharp tooling, rigid workholding. Below roughly 0.4, finish stops being a cutting outcome and becomes a separate lapping or polishing process with its own setup, inspection and scrap risk, which is why finishing cost can roughly double.
Can turning alone reach Ra 0.4 um?
On small diameters, rigid Swiss-type lathes with fine feeds and short stick-out can approach it, but it is not a promise for every geometry or material. We would prove it on a first article with a profilometer reading before committing a batch, rather than assume it from the machine badge.
What is the difference between Ra and Rz?
Ra is the average deviation of the profile; Rz is the extreme peak-to-valley height. A single scratch can push Rz out of band while Ra barely moves. Print, instrument and sampling cutoff should all use the same parameter, agreed in writing at first article, or two correct gauges will disagree.
Do you measure surface finish on first articles?
Yes, on request we report profilometer readings against the drawing call, along with dimensional inspection. Confirming the parameter and cutoff on a real part in 3-7 days is far cheaper than resolving an Ra-versus-Rz disagreement after a production batch of 7-15 days.
Send your drawings for a DFM review and a quotation
STEP, IGES, DXF, DWG or PDF — note the material, quantity and finish. Quotes usually go back within one working day. Email mc@chxmetal.com or use the quote form.