Swiss Lathe Bar Diameter Limits: What Moves to a CNC Lathe

By CHX Metal Engineering Team · Published 2026-11-15

Tsugami Swiss-type lathes in our shop take bar from 1 mm up to 20 mm; beyond that, parts route to CNC lathes that swing up to 300 mm. The crossover changes cycle time, unit cost and tolerance strategy, so it is worth settling at RFQ. A one-piece minimum makes the trial cheap.

The shaft that assumed wrong

Last quarter a buyer sent a request for 25,000 connectors a month - Ø26 mm stainless bodies, and the email said “we want Swiss-turned parts, that is the precise way”. The intent was right; the routing was not. Ø26 mm bar does not pass a Ø20 mm guide bushing, so the part was quoted on a CNC lathe instead - and the unit price came back lower than the Swiss quote would have been, because the sliding-headstock magic he was paying a premium for simply does not apply at that diameter. He accepted the routing after one email. Not every buyer asks, which is why this page exists.

The assumption behind that email is common: Swiss-type equals precision, precision equals the right choice. The process is precise because of a specific mechanical arrangement, and that arrangement only helps inside a limited band of part sizes. Outside the band you are paying for machinery you are not using.

Where the limit physically comes from

A sliding-headstock machine feeds the entire bar through a rotating guide bushing that sits millimetres from the cutting tool. The bushing is the point: it supports the workpiece right where material is removed, so a long slender part turns without deflecting. The bushing has a fixed bore, the spindle behind it has a fixed bore, and the bar has to pass through both - that is the whole constraint. Standard guide bushings on common production machines stop somewhere in the 20 to 32 mm range depending on model.

Our own fleet draws the line at 20 mm: 70 Tsugami Swiss-type lathes cover Ø1–20 mm bar, and that band is where they earn their keep - small, long, thin-walled parts finished in one hit. Above the band the support argument inverts. A Ø40 mm shaft is stiff enough relative to cutting forces that it does not need a bushing a few millimetres from the tool; a conventional CNC lathe holding it in a chuck, with or without a steady rest, holds tolerance without the guide-bushing theatre.

How routing shakes out in practice

Part ODMachine classWhyWhat changes
Ø1–20 mmSwiss-type (guide bushing)Bush-supported turning, one-hit completion, unattended runningBest unit cost at volume; minimal deburring
Ø20–80 mmCNC lathe, chuck + tailstock or steady restPart is stiff enough; bushing would add nothingTwo ops more common; slightly longer cycle
Ø80–300 mmLarge-bore CNC lathesBar stock gives way to billet or forgingsMaterial cost dominates; fixturing matters more

The bands overlap at the edges, and geometry complicates them. A Ø19 mm part with a 60 mm-long thin wall still wants the bushing; a Ø22 mm stubby fitting without Swiss support loses little. When a drawing sits near a boundary we machine both routings on a first article before quoting volume - the minimum order of one piece exists exactly for this kind of question.

What actually changes on the other side

Precision does not fall off a cliff. Tight diameters are held at ±0.005 mm on either machine class where the fit demands it; what changes is the path. Swiss work removes material once, from continuously supported bar. Chucked work often wants a second op for the back face or an internal feature, which adds handling, a fixture and a small amount of tolerance stacking between setups. For most geometries the stacked error stays well inside what a bushing would have saved; for very long, very thin parts it does not, and that is the honest line.

Cost changes more visibly. Bar-fed Swiss machines run lights-out for hours because the bushing and sub-spindle hand work off unattended; a chucked cycle usually wants an operator nearby. On Ø26 mm bodies the CNC lathe still won on price, as the opening story showed, because material utilization and cycle time beat the labour difference. Every diameter band has its own economics - which is why the routing question belongs in the quote, not in the assumptions.

Flagging the question before you quote

Three things on a drawing settle the routing quickly: the largest diameter that must spin under the headstock, the length-to-wall ratio of the thin sections, and the annual volume. Send those with the RFQ and a shop can name the machine class on day one. If a supplier quotes Swiss for everything, or CNC for everything, that itself is information - a floor running both processes, as ours does across 220 machines in Shajing, Bao'an, Shenzhen, routes by part rather than by habit. Prototypes run in 3–7 days, production in 7–15 days once the routing is agreed. Terms are EXW Shenzhen only - we are happy to recommend reliable freight forwarders.

For the wider process picture, the Swiss-type turning capability page lists machine-level detail, the sourcing guide covers vetting and cost structure, and CNC turning vs Swiss-type compares the two processes feature by feature.

I would rather answer the diameter question in an email than discover it after tooling is cut. It takes one line: max OD, wall, volume. The machines are already here - 100 machining centres, 30 of them 3+2, 50 CNC lathes, 70 Tsugamis, turning out up to 5 million pieces a month with 100+ staff across 5,000 m². Thirteen years of routing drawings have mostly taught us which questions to ask first.

Machining capacity behind this article

Address: Building B, 3rd Floor, Haosan Maozhoushan Industrial Zone, Buyong Community, Shajing Street, Bao'an District, Shenzhen  |  Tel: +86-755-27427365  |  Email: mc@chxmetal.com

Frequently asked questions

What is the maximum bar diameter a Swiss-type lathe accepts?

Common production machines stop between 20 mm and 32 mm depending on the guide bushing and spindle bore. Our Tsugami Swiss-type lathes take bar from 1 mm to 20 mm. A part larger than the bushing bore cannot be bar-fed and should be quoted on a conventional CNC lathe instead.

Can a part over 20 mm still be made on a Swiss machine?

Sometimes, from a pre-turned or pre-ground blank chucked conventionally, but that gives up the guide-bushing support that makes the process worthwhile. Routing to a CNC lathe is usually cheaper and holds tolerance just as well, since a stiff Ø26 mm part does not need bush-supported turning.

Does moving to a CNC lathe hurt tolerances?

Not in practice for stiff parts. Tight diameters are held at ±0.005 mm on either machine class where the fit needs it. The real difference is process structure: chucked work may need a second operation, which adds a fixture and small stacking between setups on very long, thin parts.

Why is Swiss turning cheaper for small parts at volume?

The bar feeds through the bushing continuously, sub-spindles hand off parts, and machines run unattended for hours, so labour per piece drops sharply. One-hit completion also removes deburring and second-op handling that chucked work usually requires.

How do I know which process my part needs before RFQ?

Send the largest spinning diameter, the length-to-wall ratio of thin sections, and annual volume. A shop running both machine classes can route it immediately; a one-piece first article in 3-7 days confirms the choice on real metal before a production run of 7-15 days is committed.

Send your drawings for a DFM review and a quotation

STEP, IGES, DXF, DWG or PDF — note the material, quantity and finish. Quotes usually go back within one working day. Email mc@chxmetal.com or use the quote form.