CNC Machining Drone Parts: Grams, Stiffness, Tolerance
By CHX Metal Engineering Team · Published 2026-11-19
A drone part is a stiffness problem before it is a tolerance problem: 7075 or 6061 aluminium at 1.2–2 mm walls carries the load, and anodising grows 5–15 µm per surface, so pilot bores are cut undersize. We hold ±0.005 mm and ship prototypes in 3–7 days.
The first document is a gram budget, not a drawing
Drone projects rarely open with a print. They open with a spreadsheet: a column of components, a column of grams, a total that has to land under the airframe target before anyone talks about process. Material, wall thickness and how many pieces get bolted together instead of cut from one block are all downstream of that column.
Which changes how a machining quote should be read. On a bracket for a machine tool, thirty extra grams costs nothing. On an arm, thirty grams at the tip is inertia the motor reverses several times a second. Bending stiffness follows the second moment of area, so a hollow 22 mm section beats a solid 12 mm one at the same mass - which is why drone parts are pockets, ribs and thin walls pushed out to the envelope.
7075 or 6061: the load path decides
Both alloys are common, and the argument between them is usually settled by one question: is this a beam in bending, or a plate carrying bearing loads and bolting to something else. 7075-T6 yields around 500 MPa against roughly 310 MPa for 6061-T6, so an arm root in 7075 runs a thinner wall for the same load, and it holds a bore well.
What 7075 does not do: it welds badly, and in the T6 temper it is more sensitive to stress corrosion than 6061, particularly with load across the short grain. Plate also carries internal stress, so a pocketed frame can bow once the outer skin comes off - a fixturing and sequencing question rather than a material one. 2024 has the fatigue behaviour but gives up corrosion resistance. The split on our floor is 7075 for primary structure, 6061 for anything holding electronics.
Thin walls are a cutting problem, not a CAD problem
A 1.2 mm wall 40 mm tall deflects under an ordinary radial load. Cut it at the rate the same tool would use in solid block and the wall springs away from the flute, the chipload drops to rubbing, and the finish comes out with chatter marks that measure fine and fatigue badly. The fix is the setup, not a slower spindle: light radial step-over, a sharp tool, a finishing pass that removes only the springback, and support on the far side of the wall where the geometry allows - sometimes a support wax.
The other half of the weight argument is part count. An arm root that was once three pieces and six fasteners can be one five-axis part, and every fastener deleted removes mass twice - the bolt, and the material around it that exists only to carry the bolt. That is where a 3+2 and simultaneous five-axis setup earns its place: reaching side features in one clamping, so position error does not accumulate across four operations. The limits are set out on the thin-wall machining page.
Anodising eats the fit, quietly
Anodising converts aluminium into oxide rather than sitting on top of it, and the layer grows both outward and inward. A Type II film of 10 µm nominal adds about 5 µm per face and consumes the same beneath, so a bore comes back roughly 10 µm undersize on diameter - several times what a motor pilot or a bearing seat allows. Hard anodising at 25–50 µm multiplies that.
So the drawing has to say which bore is a fit and which is cosmetic, and the shop cuts the fit undersize by the growth it expects. Threads are masked or chased afterwards. Colour is its own argument: the same alloy dyed the same shade will not match if the anodiser ran different current densities. The numbers are in the 6061 anodising guide.
What inspection can prove, and what it cannot
Motor mounts live and die on flatness. A mount face out by 0.05 mm tilts the motor, the prop disc runs out of plane, and the flight controller spends the afternoon chasing vibration it cannot trim out. That is measurable - CMM, or a surface plate and a dial indicator on a small part - and it belongs on the drawing as a flatness callout, not as a note about being careful. Bore roundness, position and wall thickness on a sample sit in the same category: cheap to check, expensive to find late.
What a machine shop cannot prove is that the aircraft flies. Propeller balance, motor timing, frame resonance and every airworthiness question belong to the integrator and the test bench. A dimensional report is not a flight approval, and no amount of Cpk data replaces a hover test. We hold ISO 9001:2015 and ISO 14001:2015, and report as described in inspection and FAI reporting.
Where the price actually moves
Stock removal is the first line. A pocketed frame cut from a 20 mm plate throws most of the plate away as chips, so cycle time follows how much aluminium has to leave, not the finished mass. A near-net extrusion starting 3 mm from the final surface cuts that hard, and it is worth asking whether the design tolerates the change in grain direction. Setup count is second. Anodising rack marks and masking are third, and that is the line most often missing when two quotes are compared side by side.
Volume decides the rest. At one or five pieces a five-axis part is programmed and cut one at a time. At a few hundred a month, fixtures and a second operation pay for themselves quickly. Our floor runs 220 machines - 100 machining centres, 30 of them 3+2, with 50 CNC lathes and 70 Tsugami Swiss-type units for the small round parts that hang off a frame - and capacity reaches 5 million pieces a month.
| Field | CHX Metal |
|---|---|
| Location | Shajing, Bao'an, Shenzhen, China - 5,000 m² plant, 100+ staff, machining since 2013 |
| Equipment | 220 machines: 100 machining centres (30 of them 3+2), 50 CNC lathes, 70 Tsugami Swiss-type lathes |
| Tolerances | ±0.005 mm on critical features; unmarked dimensions to ISO 2768-m; CMM and optical measurement |
| MOQ | 1 piece |
| Lead times | Prototypes 3–7 days; production 7–15 days; capacity to 5 million pieces per month |
| Materials | 6061-T6 and 7075-T6 aluminium, 2024 on request, 303/304/316L stainless, TC4 titanium, H59 brass; ISO 9001:2015 and ISO 14001:2015 certified |
| Shipping | EXW Shenzhen only - we are happy to recommend reliable freight forwarders. |
Machining capacity behind this article
- Equipment: 220 machines — 100 machining centres (30 of them 3+2), 50 CNC lathes, 70 Tsugami Swiss-type lathes.
- Tolerance: ±0.005 mm on critical features; anything unmarked defaults to ISO 2768-m.
- Volume: up to 5 million pieces a month; prototyping 3–7 days, production 7–15 days.
- Materials: 6061/7075 aluminium, 303/304/316 stainless, H59 brass, copper, TC4 titanium, carbon steel.
- Footprint: 5,000 m² in Shajing, Bao'an, Shenzhen; 100+ staff; founded 2013.
- Terms: EXW Shenzhen only — we are happy to recommend reliable freight forwarders.
Address: Building B, 3rd Floor, Haosan Maozhoushan Industrial Zone, Buyong Community, Shajing Street, Bao'an District, Shenzhen | Tel: +86-755-27427365 | Email: mc@chxmetal.com
Frequently asked questions
Which aluminium should a drone frame be made from?
7075-T6 where the part is a beam in bending and the wall has to be thin - arm roots, landing gear legs, motor mounts. 6061-T6 for housings, camera brackets and avionics trays, because it welds, anodises evenly and takes impact without cracking. 7075 is about 500 MPa yield against roughly 310 MPa for 6061, and it is the more sensitive of the two to stress corrosion in the T6 temper.
Can you machine 1 mm aluminium walls without chatter?
Yes, with the right setup rather than a slower spindle. That means light radial step-over, a sharp tool, a finishing pass that removes only the springback, and support on the far side of the wall where geometry allows - sometimes a support wax. On a 40 mm tall wall, chatter is a fixture and toolpath problem before it is a machine problem.
Does anodising change the size of a bore?
It does. A Type II film of 10 µm nominal grows roughly 5 µm outward and consumes about the same beneath, so a bore comes back undersize by around 10 µm on diameter - several times a typical motor pilot tolerance. Hard anodising at 25–50 µm multiplies that. The bore is cut undersize by the expected growth, and threads are masked or chased afterwards.
Do you provide airworthiness or flight certification?
No. We machine to the drawing and report dimensions, flatness, bore position and material certificates. Propeller balance, frame resonance and airworthiness approval belong to the integrator and the test bench. We hold ISO 9001:2015 and ISO 14001:2015 and do not claim aerospace certification we do not have.
What is the minimum order and how fast can samples arrive?
One piece, and prototypes typically run 3–7 days from a released drawing, with production at 7–15 days. Thin-wall frames are usually quoted with a short first-article run before a batch, because wall thickness and flatness after machining are the two numbers most likely to need a tweak.
Send your drawings for a DFM review and a quotation
STEP, IGES, DXF, DWG or PDF — note the material, quantity and finish. Quotes usually go back within one working day. Email mc@chxmetal.com or use the quote form.